Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
What are your thoughts and feelings on Installing A Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult task. If the old tub is readily accessible, the job can move easily; if you have to open a wall to remove the old tub and also place the new bathtub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and also set in the new one. Ensure you have qualified yourself for the task as well as are comfortable trying it. Instead of hiring a professional to take over a halfway-completed task, it is far better to think about using one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This article will assist you install a new bathtub in your washroom if you have actually currently gotten a brand-new tub and also don't need to transform the plan of your previous water supply pipes.
Your tools and product list should make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area between the faucet and also the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind ought to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Using the two wood boards under its feet, place the tub in the required placement. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bathtub up until the level reads level.
To install taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Switch on the supply of water as well as examine all joints and also new pipework for leakages as well as tighten them if necessary. Load the tub and likewise inspect the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bathtub needs to wait till the tub has been utilized at the very least once as this will resolve it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure supplied with the bath needs to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, triggering the water to permeate the wall between the bathroom and the tiling, bring about complications with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and installations. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can crack relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our topic on A Step-by-Step Guide to Installing a Bathtub. Many thanks for spending some time to read through our piece. In case you enjoyed reading our article if you please be sure to pass it around. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
We've got this! Report this page